HighlightsVery low mass textile soft dome diaphragmOptimized magnet system with double magnetLow damping magnetic fluid coolingFully Vented Motor System for Low compression8 ohm, positive terminal with white paint markReplaceable voice coil assemblyBlack Die-Cast Aluminum Face PlateMade in Denmark Product details Scan-Speak Discovery D2608/913000 1" Textile Dome Tweeter The Discovery tweeter uses a very light, low mass “soft dome" with high internal damping, and a highly-optimized, low-compression magnet system, which was designed especially for the low mass dome. The result is a driver that has both good sensitivity and an impressive range into the lower frequencies. The low mass dome, coupled with a fully vented motor system provides non-compressed sound reproduction over the entire frequency response. This combination allows the Discovery tweeter to be used in systems with lower cross-over points than is recommended for most normal tweeters, making this product a powerful tool for any acoustic designer in the process of tuning a system. Specifications: Compliance Equivalent Volume (Vas): 0.0007 ft.³ • BL Product (BL): 2.6 Tm • Mechanical Compliance of Suspension (Cms): 0.29 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.18 g • Maximum Linear Excursion (Xmax): 0.5 mm • Surface Area of Cone (Sd): 7 cm2Show more Show less

Highlights1" Textile Dome DiaphragmLow Resonant Rear Chamber4 ohmFerro FluidBlack Painted Alu Face Plate Product details Scan-Speak Classic D2904/950000 1" Textile Dome Tweeter The Classic tweeters are among the many highly praised designs in Classic series. They have enjoyed success over 3 decades. And still among the best tweeters available. The D2905/9000 tweeter kick started a new era with a line of very high quality 1" tweeters, today known as -9300, -9500, -9700 and 9800. Despite their many years on the market still used in many top High-End speakers around the world. Specifications: Compliance Equivalent Volume (Vas): 0.0007 ft.³ • BL Product (BL): 3.2 Tm • Mechanical Compliance of Suspension (Cms): 0.19 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.45 g • Maximum Linear Excursion (Xmax): 0.1 mm • Surface Area of Cone (Sd): 9.5 cm2Show more Show less

Highlights1" Textile Dome DiaphragmPatented Symmetrical Drive (SD-2) motorDie Cast Rubber Painted Alu Face PlateLarge Roll Surround for Wide DispersionAirCirc Motor Design w. 6 Neo magnets Product details Scan-Speak Illuminator D3004/660000 1" Textile Dome Tweeter The Illuminator tweeters stand for superb vocal rendition and excellent imaging at all listening locations. Its large roll surround and textile dome diaphragm provides a flat frequency response to above 30KHz with outstanding off-axis dispersion. The unique AirCirc Magnet System, and its rear chamber, results in elimination of reflections and resonances that compromise the performance of traditional motors. Specifications: Compliance Equivalent Volume (Vas): 0.0007 ft.³ • BL Product (BL): 2.3 Tm • Mechanical Compliance of Suspension (Cms): 0.33 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.35 g • Maximum Linear Excursion (Xmax): 0.2 mm • Surface Area of Cone (Sd): 7 cm 2Show more Show less

HighlightsHigh Performance TweeterLow Damping Ferrofluid CoolingLinear response faceplate with neutral designCoated Textile DiaphragmHigh StabilityDampened Cavity in Pole Piece Product details Scan-Speak Discovery D2606/920000 1" Coated Textile Dome Tweeter The Discovery series offer traditional design, superior sound, a solid construction, and a wide range of variants. Combining these elements - plus a wealth of technical features and finesses - it gives our customers the possibility of acquiring a tailor-made Scan-Speak solution with very good performance at a reasonable low price point! Specifications: Compliance Equivalent Volume (Vas): 0.0003 ft.³ • BL Product (BL): 2.7 Tm • Mechanical Compliance of Suspension (Cms): 0.07 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.3 g • Maximum Linear Excursion (Xmax): 0.2 mm • Surface Area of Cone (Sd): 7.1 cm2Show more Show less

HighlightsHigh Performance 1" TweeterCoated Textile DiaphragmBraided tinsel leadsLow Damping Ferrofluid Cooling for High StabilityDouble ChamberNeutral face plate design Product details Scan-Speak Discovery D2606/922000 1" Coated Textile Dome Tweeter The Discovery series offer traditional design, superior sound, a solid construction, and a wide range of variants. Combining these elements - plus a wealth of technical features and finesses - it gives our customers the possibility of acquiring a tailor-made Scan-Speak solution with very good performance at a reasonable low price point! Specifications: Compliance Equivalent Volume (Vas): 0.0003 ft.³ • BL Product (BL): 2.8 Tm • Mechanical Compliance of Suspension (Cms): 0.11 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.33 g • Maximum Linear Excursion (Xmax): 0.2 mm • Surface Area of Cone (Sd): 7.1 cm2Show more Show less

HighlightsBeryllium Diaphragm (99% Pure Be)Patented Symmetrical Drive (SD-2) motorBlack Rubber Painted Die Cast FaceplateAirCirc Motor Design with 6 Neodymium magnetsLarge Roll Surround f. Wide DispersionNon-Magnetic Sound Transparent Protective Grill Product details Scan-Speak Illuminator D3004/664000 1" Beryllium Dome Tweeter This tweeter features a 99% pure Beryllium dome diaphragm. The large roll surround and Beryllium dome diaphragm provide a flat frequency response to above 40KHz with outstanding off-axis dispersion and a silky-smooth sound. Scan-Speak's unique AirCirc Magnet System - named for the way it optimizes air flow within the chamber – rearranges the traditional magnet structure from a single magnet to an open magnetic circuit comprised of six separate neodymium slugs. This, in combination with the chamber, results in the elimination of the reflections and resonances that compromise the performance of traditional motors. The D3004-664000 gives engineers improved control over critical midrange performance, for superb vocal rendition and excellent imaging at all listening locations. Specifications: Compliance Equivalent Volume (Vas): 0.0007 ft.³ • BL Product (BL): 2.3 Tm • Mechanical Compliance of Suspension (Cms): 0.29 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.35 g • Maximum Linear Excursion (Xmax): 0.2 mm • Surface Area of Cone (Sd): 7 cm2Show more Show less

HighlightsPatented Symmetrical Drive (SD-2) motorHand coated 1" Textile Dome DiaphragmLow Resonance Rear ChamberBlack Aluminium Face PlateLow viscosity Ferro Fluid Product details Scan-Speak D2905/970000 1” Dome Tweeter 6 Ohms The Scanspeak D2905/970000 has a high power handling of 225W and a frequency response of above 30KHz. Features include a hand-coated 25mm soft textile dome, an airflow optimized copper capped pole piece and a tuned rear chamber with an integral resonance damping plug. This tweeter also benefits from the Scanspeak SD2 'Symmetrical Drive' system incorporating a copper capped and sleeved center pole piece;  this effectively forms a very low impedance shorted turn (called a Faraday ring) within the magnet circuit, the net result being that the voice coil impedance remains largely constant across it's operating frequency range resulting in a more linear output with greater top-end extension. This is a highly advanced design with a sweet, detailed sound. Found in many high-end designs and is a top choice for DIY high-performance loudspeakers.Show more Show less

Highlights1" Beryllium Diaphragm (99% pure Be)High Efficiency (90.2dB) and Low Resonance (450Hz)Patented Symmetrical Drive (SD-2) motorNon-Resonant Alu Rear ChamberNeodymium MagnetAluminum Face Plate and ChamberSound Transparent Protective Grill61.9mm (2.44") diameter flange with 55.4mm (2.19") depthExcellent choice for both home hi-fi and autosound applications Product details Scan-Speak Illuminator D3004/604010 1" Beryllium Dome Tweeter This 1” compact Illuminator beryllium tweeter is an example of a big sound in a small body. As beryllium is a material characterized by great stiffness, light weight and high damping, the beryllium diaphragm offers all the properties required to reproduce excellent sound. Indeed, the D3004/604010 sounds fantastic. It has very low distortion and a distinct clarity that brings out the best in all types of music. Some have described the sound as holographic. The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. The D3004-604010 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces. The back chamber is die cast in aluminum and designed with a contoured shape that functions as a heat sink in high power applications. Specifications: Compliance Equivalent Volume (Vas): 0.001 ft.³ • BL Product (BL): 1.7 Tm • Mechanical Compliance of Suspension (Cms): 0.43 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.35 g • Maximum Linear Excursion (Xmax): 0.2 mm • Surface Area of Cone (Sd): 7 cm2Show more Show less

HighlightsBeryllium Diaphragm (99% Pure Be)Patented Symmetrical Drive (SD-2) motorBlack Anodized Ø120mm Machined Alu FaceplateRear Mount Magnet SystemTitanium Voice Coil FormerNon Resonant Aluminum Rear Chamber Product details Scan-Speak Revelator D2908/714000 1" Beryllium Dome Tweeter The D2908/714000 is a highly efficient and high-power 8 ohm 1" beryllium dome tweeter, it reproduces music clean and clear at all listening levels with dynamic precision and a superb vocal rendition as when recorded. The smooth machined alu faceplate and the acoustical very transparent wire-mesh protection grille not only represent a beautiful appearance is also allows the sound to be dispersed free and undistorted to the listener. Specifications: Compliance Equivalent Volume (Vas): 0.0007 ft.³ • BL Product (BL): 3.6 Tm • Mechanical Compliance of Suspension (Cms): 0.26 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.33 g • Maximum Linear Excursion (Xmax): 0.4 mm • Surface Area of Cone (Sd): 7 cm2Show more Show less

Highlights1" Textile Dome DiaphragmMagnet System w. Alu RingDiffraction Damping Rubber FrontLarge Roll Surround f. Wide DispersionAirCirc Motor Design w. 6 Neo magnetsDie Cast Rubber Painted Alu Face Plate Product details Scan-Speak Illuminator D3004/662000 1" Textile Dome Tweeter The Illuminator tweeters stand for superb vocal rendition and excellent imaging at all listening locations. Its large roll surround and textile dome diaphragm provides a flat frequency response to above 30KHz with outstanding off-axis dispersion. The unique AirCirc Magnet System, and its rear chamber, results in elimination of reflections and resonances that compromise the performance of traditional motors. Specifications: Compliance Equivalent Volume (Vas): 0.0007 ft.³ • BL Product (BL): 2.3 Tm • Mechanical Compliance of Suspension (Cms): 0.29 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.35 g • Maximum Linear Excursion (Xmax): 0.2 mm • Surface Area of Cone (Sd): 7 cm2Show more Show less

Our SILVER SERIES are specially selected units from Scan-Speak's well-known home audio speakers. Which have been optimized for automotive use. This series enables audiophiles to experience in their vehicle the – TRUE TO LIVE – that they enjoy from their high-end home audio system. Highlights1" Textile Dome DiamphragmPatented Symmetrical Drive (SD-2) motorPatented Symmetrical Drive (SD-2) motorLarge Roll Surround f. Wide DispersionSound Transparant Protective GrillDie Cast Housing & Face Plate Product details Scan-Speak Silver Series D3004/602006 Dome Tweeter with Grill The Scan-Speak Silver Series D3004/602006 Dome Tweeter is a high-performance 1" (25mm) textile dome tweeter that is designed for automotive use. It features a patented Symmetrical Drive (SD-2) motor, a non-resonant aluminum rear chamber, and a large roll surround for wide dispersion. The tweeter is also equipped with a neodymium magnet and a protective multi-hex grille. The D3004/602006 has a frequency response of 2,200 to 20,000 Hz, a sensitivity of 92 dB, and an impedance of 4 ohms. It is rated at 40 watts RMS and 80 watts peak power.Show more Show less

Highlights1" Textile Dome with Large Roll Surround for Wide DispersionPatented Symmetrical Drive (SD-2) motorShallow Non Resonant Alu Rear ChamberRing Neodymium MagnetAluminum Face Plate and ChamberSound Transparent Protective Grill61.9mm (2.44") diameter flange with 21.5mm (.85") depthExcellent choice for both home hi-fi and autosound applications Product details Scan-Speak Illuminator D3004/602000 1" Textile Dome Tweeter The Illuminator tweeters continue with the heritage of the renowned Revelator series. The large-roll surround and textile dome diaphragm provide a flat frequency response to above 30KHz with outstanding off-axis dispersion. The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. D3004-602000 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces. The back chamber is die cast in aluminum and designed with a contoured shape that functions as a heat sink in high power applications. Specifications: Compliance Equivalent Volume (Vas): 0.0003 ft.³• BL Product (BL): 1.7 Tm • Mechanical Compliance of Suspension (Cms): 0.15 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.35 g • Maximum Linear Excursion (Xmax): 0.2 mm • Surface Area of Cone (Sd): 7 cm2Show more Show less

Highlights1" Coated Textile DiaphragmPatented Symmetrical Drive (SD-2) motorNon Resonant Alu Rear ChamberLarge Roll Surround for Wide DispersionLarge Ring Neo Magnet for High OutputSilver Anodized Machined Alu Face Plate Product details Scan-Speak Revelator D2904/710002 1" Coated Textile Dome Tweeter The Scan-speak D2904-710002 tweeter is a 1" soft dome with wide surround, using the same chambering as the Ring Radiator. The carefully designed dome and surround result in a linear response and an exceptionally good off axis response. Note the smooth roll off on the low end, making this tweeter an excellent choice for simple slopes. A specially designed venting system uses a needle to cut down on turbulence in the air cavity. Better dynamics are achieved by not using ferrofluid, voice coil cooling is performed by the venting system and conduction through copper rings. The new SD-2 neodymium magnet system improves transient response. Specifications: Compliance Equivalent Volume (Vas): 0.0007 ft.³ • BL Product (BL): 2.8 Tm • Mechanical Compliance of Suspension (Cms): 0.23 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.4 g • Maximum Linear Excursion (Xmax): 0.2 mm • Surface Area of Cone (Sd): 7 cm2Show more Show less

Highlights1" Textile Dome DiaphragmLow Resonant Rear ChamberFerro FluidBlack Painted Alu Face Plate Product details Scan-Speak Classic D2905/950000 1" Textile Dome Tweeter The Classic tweeters are among the many highly praised designs in Classic series. They have enjoyed success over 3 decades. And still among the best tweeters available. The D2905/9000 tweeter kick started a new era with a line of very high quality 1" tweeters, today known as -9300, -9500, -9700 and -9800. Despite their many years on the market still used in many top High-End speakers around the world. Specifications: Compliance Equivalent Volume (Vas): 0.0007 ft.³ • BL Product (BL): 3.5 Tm • Mechanical Compliance of Suspension (Cms): 0.19 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.45 g • Maximum Linear Excursion (Xmax): 0.4 mm • Surface Area of Cone (Sd): 8.5 cm2Show more Show less

Highlights1" Textile Dome DiaphragmPatented Symmetrical Drive (SD-2) motorLarge Non Resonant Alu Rear ChamberLarge Roll Surround f. Wide DispersionSound Transparent Protective GrillDie Cast Housing & Face Plate Product details Scan-Speak Illuminator D3004/602010 1" Textile Dome Tweeter The compact size is one of the key elements of these Illuminator tweeters, which provides a high degree of flexibility within design options. The small size is employed without compromising sound quality where these compact tweeters are fully comparable to the renowned full size Illuminator and Revelator tweeters, no matter if the music is played at high or low listening levels. Specifications: Compliance Equivalent Volume (Vas): 0.001 ft.³ • BL Product (BL): 1.7 Tm • Mechanical Compliance of Suspension (Cms): 0.40 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.35 g • Maximum Linear Excursion (Xmax): 0.2 mm • Surface Area of Cone (Sd): 7 cm2Show more Show less

Highlights1" Beryllium Diaphragm (99% pure Be)High Efficiency (90.9dB) and Low Resonance (750Hz)Patented Symmetrical Drive (SD-2) motorShallow Non Resonant Alu Rear ChamberNeodymium MagnetAluminum Face Plate and ChamberSound Transparent Protective Grill61.9mm (2.44") diameter flange with 21.5mm (.85") depthExcellent choice for both home hi-fi and autosound applications Product details Scan-Speak Illuminator D3004/604000 1" Beryllium Dome Tweeter This 1” compact Illuminator beryllium tweeter is an example of a big sound in a small body. As beryllium is a material characterized by great stiffness, light weight and high damping, the beryllium diaphragm offers all the properties required to reproduce excellent sound. Indeed, the D3004/604000 sounds fantastic. It has very low distortion and a distinct clarity that brings out the best in all types of music. Some have described the sound as holographic. The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. The D3004-604000 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces. The back chamber is die cast in aluminum and designed with a contoured shape that functions as a heat sink in high power applications. Specifications: Compliance Equivalent Volume (Vas): 0.0003 ft.³ • BL Product (BL): 1.20 Tm • Mechanical Compliance of Suspension (Cms): 0.19 mm/N • Diaphragm Mass Inc. Airload (Mms): 0.24 g • Maximum Linear Excursion (Xmax): 0.2 mm • Surface Area of Cone (Sd): 7 cm2Show more Show less