Showing 1–20 of 40 resultsSorted by latest
Markaudio Alpair-7MS Gold 4″ Full Range Woofer
The advanced design Alpair 7MS (mono suspension) is a radical departure from previous models. The 7MS is completely new, utilising many new design components and manufacturing processes. The two main features are the patent-pending Negative Camber Cone and Mono suspension system. Other key features include a custom designed, gas-flowed glass-fibre chassis and dedicated ultra light voice coil. HighlightsLatest model.The run-in time for the 7MS is significantly reduced compared to previous models. Ten hours of light music at moderate volumes is sufficient for the suspension to reach its optimal operating pattern.An Arrestor (as deployed in previous Alpair models) provides an audible warning of the accidental excess excursion.The low-mass coil has a vented former and the motor employs a custom made copper plating to reduce distortion.The MS7 is a bass capable audio driver with comparable performance to light-medium load traditional mid-bass units of the same size. Product details Markaudio Alpair-7MS Gold 4" Full Range Woofer  After releasing the Pluvia range of drivers, which have been well-received, Mark set about the next design evolution. As some of you will know Mark's design ethos is mechanical efficiency, adding lightness and simplifying where possible. In these new drivers, Mark has managed to achieve much more with much less. The advanced design Alpair 7MS (mono suspension) is a radical departure from previous models. The 7MS is completely new, utilizing many new design components and manufacturing processes. The two main features are the patent-pending Negative Camber Cone and Mono suspension system. Other key features include a custom-designed, gas-flowed glass-fiber chassis and dedicated ultralight voice coil. The 7MS cone is an ultra-shallow design affording a wide dispersion pattern. The outer section of the cone profile is angled backward creating a +180 degrees emittance pattern to help optimize stereo imaging. Vocals from quality sources sound more natural and detailed as the center cap and cone profile are geometrically close-aligned. Much technical research has been done to balance the driver's powertrain (cone, cap, coil, and suspension) between its axis of travel and the corresponding center of gravity. The new negative-camber cone facilitates the repositioning of the coil to avoid the need for a traditional rear suspension (spider). Mark's new mono suspension design frees the coil from having a restrictive spider bonded to it, improving the transfer of energy from the driver's motor to its cone. The new suspension employs an all-new custom mix of four synthetic materials, resulting in improved linearity under low-frequency loads. The various slopes and rounded angles help improve sound wave emittance. Custom extended terminals are provided for push-on connectors or light-soldering for cables up to 1.5mm diameter. The 7MS is an audio driver designed for the dedicated music lover and High-Fidelity enthusiast. Attention to design detail along with a close tolerance manufacturing standard to +/- 0.05mm on most component alignments make this new generation of Markaudio transducers stand out from the crowd.Show more Show lessMarkaudio CHR-70 Champagne 4″ Full Range Aluminium Woofer
The MarkAudio CHR-70 has a light easy sound, a little warm, not so "shaped" so it will suit the listening tastes of many people. Its cone gives much musical detail and makes a very clear sound. HighlightsThe latest model, 3rd generationSynthetic rubber surroundNomex spiderImproved voice coil former Product details Markaudio CHR-70 Champagne 4" Full Range Aluminium Woofer  The CHR-70 (Gen. 3) is now up-dated 3 times since the first model was launched nearly 3 years back. This Gen. 3 driver has more high range performance. The frequency range now goes higher to 25-kHz. Bass response in the properly designed box can go low to just under 40Hz. It has a light easy sound, a little warm, not so "shaped" so it will suit the listening tastes of many people. Its cone gives much musical detail and makes a very clear sound. The driver has a medium efficiency of 85.5 dB at 8 Ohms making it easy to use on nearly all small to medium power amplifiers. The driver can easily fit into Bass-reflex and Vented box sizes from 4.4 liters to 10 liters internal volume. Many technical improvements have been made. Improved stiffer frame. New cap design with a new improved fitting method. New Japanese designed coil. New spider for improved bass. The new CHR-70 Gen. 3 is an excellent high-end and multi-purpose driver. Its also suitable for many computers, Home Theatre, TV, and commercial A/V applications.Show more Show lessMarkaudio Tozzi Two Silver Speaker
Tozzi Two is an ultra-high-end, single-driver desktop loudspeaker. It incorporates the most advanced all-range driver technology on the market with a sub-compact enclosure developed using the latest in industrial design and computer numerical control (CNC) machining. Tozzi Two, in finished quality and performance, is a purist high-end compact loudspeaker for the discerning customer.  HighlightsSilver variantState-of-the-art 50mm Sota 5A variant single-suspension all-range driverHigh-rigidity enclosure milled from solid aerospace-grade 
aluminium and composite sub-assembliesTwo high-grade finishesMachined waveguide front baffleBase includes mounting for 1â„4†thread tripods or similar stands Product details Markaudio Sota Tozzi Two Silver Speakers  Designed by Mark Fenlon, this state-of-the-art driver is a single-suspension variation of the Sota 5. The sound has superb clarity and detail, with a clean, precise and phase-accurate balance. A long stroke helps avoid excess compression. Range is exceptional for a sub-compact loudspeaker, stretching from upper bass notes to well beyond the upper limit of human hearing. The advanced alloy cone has a very shallow profile, and with the signature Tozzi waveguide, gives excellent dispersion of sound energy into the room. No filter is used; the output of the amplifier goes direct to the driver. Features   BUILT FROM THE GROUND UP MarkAudio-SOTA loudspeakers are built from the ground up, including the cabinets, crossovers and speaker drivers. Many manufacturers choose off-the-shelf components that aren't always a perfect match to their system design targets, MarkAudio-SOTA, purists by engineering standards, build their components to precisely match the specific design characteristics of the speaker systems.   ALL-RANGE DRIVER APPROACH MarkAudio-SOTA's unique all-range approach offers the rich midrange that is typical of a wide-range single speaker design, while providing a full frequency range extending from 80Hz to 25kHz, and the high-impact dynamics of more typical multi-way speakers. Using an advanced 50mm Sota 5 all-range driver, its low mass mixed-alloy cone provides superior transparency and detail.     SYMMETRICAL SOUND FIELD MarkAudio-SOTA uses its own symmetrical technology. The dual, wide dispersion, shallow-profile cone drivers replace conventional cone-woofer and dome-tweeter combinations. With their matched dispersion and output characteristics, along with a minimal crossover slope, the two custom-made Sota drivers provide an audibly seamless integration between high and low frequencies. This integration results in a smooth, natural output and soundstage that affords a wider range of seating positions, allowing several people to hear a top quality performance at one time.   ADVANCED CABINET ENGINEERING Tozzi One is constructed from three rigid sub-structures. They are made from a composite of Acrylonitrile-Butadiene- Styrene with reinforcing fibres. These can be produced to exceptional tolerances, have a long service life and are cosmetically attractive. The front and central sub-structures are precision aligned and bonded to create a stable primary assembly. The rear panel is then mechanically secured, completing the structure.    STYLING Tozzi One was developed by Mark Fenlon, the British engineer responsible for the internationally acclaimed Alpair loudspeaker drive units. Mark's concept was to develop a sub-compact loudspeaker to partner our flagship Viotti One standmount, using advanced composite materials that suit modern decor and living requirements.  The size and styling echoes compact high-quality cameras, and Tozzi One can be mounted on any standard camera or photo-light tripod, making it a great lifestyle icon in modern living spaces. It can also be used on desktops, shelves or wall brackets. Three choices of finish are available, giving a fresh, modern appearance to this unique product.Show more Show lessMarkaudio Tozzi One Kit White DIY Kit Components and Cabinets | Pair
HighlightsStylish & rigid composite enclosure constructed from 3 sub-structuresThree color schemes to choose from: Black, Red, and White.Waveguide front baffleBase includes a threaded insert for 1â„4†thread for tripods or stands Product details Markaudio Tozzi One Kit White| DIY Kit | Components and Cabinet | Pair The Tozzi One is a compact high-fidelity pure point source loudspeaker system designed by Mark Fenlon. It is easy to self-assemble and when completed, becomes a high-class product that stands above other loudspeaker kits. The CHN50 used in the Tozzi One is a high performance affordable full-range drive unit which directly mounts into the kit's front panel, and the Tozzi One enclosure was developed and tuned by Mark to operate optimally with this high-technology drive. The CHN50 are included in the kit.Show more Show lessMarkaudio Tozzi One red DIY speaker kit
HighlightsStylish & rigid composite enclosure constructed from 3 sub-structuresThree color schemes to choose from: Black, Red, and White.Waveguide front baffleBase includes a threaded insert for 1â„4†thread for tripods or stands Product details Markaudio Tozzi One Kit Red | DIY Kit | Components and Cabinets | Pair The Tozzi One is a compact high-fidelity pure point source loudspeaker system designed by Mark Fenlon. It is easy to self-assemble and when completed, becomes a high-class product that stands above other loudspeaker kits. The CHN50 used in the Tozzi One is a high performance affordable full-range drive unit which directly mounts into the kit's front panel, and the Tozzi One enclosure was developed and tuned by Mark to operate optimally with this high-technology drive. The CHN50 are included in the kit.Show more Show lessMarkaudio Tozzi One black DIY speaker kit
HighlightsStylish & rigid composite enclosure constructed from 3 sub-structuresThree color schemes to choose from: Black, Red, and White.Waveguide front baffleBase includes a threaded insert for 1â„4†thread for tripods or stands Product details Markaudio Tozzi One Kit Black| DIY Kit | Components and Cabinets | Pair The Tozzi One is a compact high-fidelity pure point source loudspeaker system designed by Mark Fenlon. It is easy to self-assemble and when completed, becomes a high-class product that stands above other loudspeaker kits. The CHN50 used in the Tozzi One is a high performance affordable full-range drive unit which directly mounts into the kit's front panel, and the Tozzi One enclosure was developed and tuned by Mark to operate optimally with this high-technology drive. The CHN50 are included in the kit.Show more Show lessMarkaudio PLUVIA-7PHD Full-range Woofer
The new paper-cone Pluvia 7 PHD was developed with the attractive paper cone, unique suspension and low-mass coil which is wound in high-purity rectangular section copper. The Thiele / Small characteristics are engineered to allow surprising bass performance from a compact drive unit. HighlightsLatest-modelBlue 4'' natural uncoated paper coneWide operating range –rolled off high frequencies for vintage toneLow cone profile –very broad directivity patternAdvanced low-distortion motor designLong-stroke suspension with excursion arrestor and progressive-rate spiderLow-profile surface-mount reinforced polymer basket Product details Markaudio Pluvia 7 PHD Full-range Woofer The new paper-cone Pluvia seven PHD was developed due to requests from the DIY audio community for a return of paper cone drivers to the latest Markaudio drivers. Its response balance was carefully engineered to provide a shelved down treble and emphasized upper midrange output to address specific requests. The attractive paper cone, suspension, and low-mass coil, wound in high-purity rectangular section copper are unique to this model, and the Thiele / Small characteristics engineered to allow surprising bass performance from a compact drive unit. The frame is the familiar, high-quality Pluvia design, which may be conveniently surface or flush-mounted, and has a very open design, allowing good air-flow to the rear of the cone. The sound balance is warm, with emphasized upper midrange, and soft treble. Jazz followers in Asia played a role in the final tuning of this driver. Those enthusiasts into vintage and mono recordings using warm tube (valve) amplification may have a particular interest in this driver.Show more Show lessMarkaudio PLUVIA-7HD Gold Full-range Woofer
The second-generation Pluvia 7HD is designed to supersede our original Alpair 7 series drive units. It employs many of the same components, and has a very similar balance of frequency response and Thiele / Small values to the old Alpair model, packaged in the more efficient and convenient Pluvia frame. HighlightsVintage Gold 4'' magnesium alloy coneOperating range to 30KHz - very linear responseVery shallow multiform cone profile – very broad directivity patternAdvanced low-distortion motor designLong-stroke suspension with arrestor and progressive-rate spiderLow-profile surface-mount reinforced polymer basket Product details Markaudio PLUVIA-7HD Gold Full-range Woofer The second-generation Pluvia 7HD is designed to supersede our original Alpair 7 series drive units. It employs many of the same components and has a very similar balance of frequency response and Thiele / Small values to the old Alpair model, packaged in the more efficient and convenient Pluvia frame. With a mounting depth of less than 4mm, the Pluvia may be surface or flush-mounted, and the design of the mounting legs is very open, allowing good airflow to the rear. The low-mass coil, suspension, and shallow-profile cone are highly efficient. Frequency response extends beyond 30KHz, and the generous 4mm (1-way) Xmax and conveniently balanced T/S parameters allow 40Hz bass output in suitable enclosure designs. The sound character is neutral and highly detailed, with excellent off-axis performance. It is an extremely flexible drive unit for music, small HT and commercial AV applications, and offers exceptional performance at an affordable price point.Show more Show lessMarkaudio PLUVIA-7HD Chrome Full-range Woofer Soft Chrome
The second-generation Pluvia 7HD is designed to supersede our original Alpair 7 series drive units. It employs many of the same components, and has a very similar balance of frequency response and Thiele / Small values to the old Alpair model, packaged in the more efficient and convenient Pluvia frame. HighlightsVintage Gold 4'' magnesium alloy coneOperating range to 30KHz - very linear responseVery shallow multiform cone profile – very broad directivity patternAdvanced low-distortion motor designLong-stroke suspension with arrestor and progressive-rate spiderLow-profile surface-mount reinforced polymer basket Product details Markaudio Pluvia 7 HD Chrome Full-range Woofer The second-generation Pluvia 7HD is designed to supersede our original Alpair 7 series drive units. It employs many of the same components and has a very similar balance of frequency response and Thiele / Small values to the old Alpair model, packaged in the more efficient and convenient Pluvia frame. With a mounting depth of less than 4mm, the Pluvia may be surface or flush-mounted, and the design of the mounting legs is very open, allowing good airflow to the rear. The low-mass coil, suspension, and shallow-profile cone are highly efficient. Frequency response extends beyond 30KHz, and the generous 4mm (1-way) Xmax and conveniently balanced T/S parameters allow 40Hz bass output in suitable enclosure designs. The sound character is neutral and highly detailed, with excellent off-axis performance. It is an extremely flexible drive unit for music, small HT and commercial AV applications, and offers exceptional performance at an affordable price point.Show more Show lessMarkaudio PLUVIA-11 Grey 7″ Full Range Aluminium Woofer
The Pluvia 11 is a completely new driver design. It is the first “full range†driver that can handle bass loads typically delivered by 5.5 inch to 6.5 inch mid-bass units used in most 2 way systems. HighlightsSynthetic rubber surroundSuper-strength alloyImproved bass handelingImproved dust cap Product details Markaudio Pluvia-11 Grey 7†full Range Aluminium woofer The Pluvia 11 is a completely new driver design. It is the first “full range†driver that can handle bass loads typically delivered by 5.5 inch to 6.5 inch mid-bass units used in most 2 way systems. The Pluvia 11 cone is an entirely new design from Mark Fenlon. It uses a new super-strength aerospace grade alloy designed to cope with high bending stress loads. The material thickness is increased by 50% over previous Markaudio designs, yet the profile remains shallow to increase dispersion. Two more processes have been added to the Multiform cone production sequence to increase Pluvia 11's operational low frequency load capacity. The all-new front suspension has a variable thickness geometry, increasing oscillatory stability by 30% over previous designs. The rear suspension (spider) has an operational surface area 25% larger than the Alpair 10 to cope with load demands of typical mid-bass units. However, the Pluvia 11's high range has not been sacrificed. It outperforms the smaller Alpair 10 by reaching slightly higher frequencies with an improved spread on the high-range lift above 10kHz. Other design advances include the new “easy install†frame. This new-technology one-piece moulding utilises a GF30 glass fibre and resin mix. Pluvia 11's frame is more rigid than previous designs, with a mounting depth of only 4.5mm, making both recessed and surface-mounting simple. Two new cone colours add visual interest. Along with the Pluvia 7, this new family of drivers will serve custom builders well into the future. For the first time in the history of traditional full-range driver design, users now have a genuine choice to go full-range without sacrificing bass handling, or use it as a wide-range mid-bass driver that allows simple filtering. The new Pluvia 11 is an excellent high-end and multi-purpose driver. It's also suitable for many computer, Home Theatre, TV, and commercial A/V applications.Show more Show lessMarkaudio PLUVIA-11 Gold 7″ Full Range Aluminium Woofer
The Pluvia 11 is a completely new driver design. It is the first “full range†driver that can handle bass loads typically delivered by 5.5 inch to 6.5 inch mid-bass units used in most 2 way systems. HighlightsSynthetic rubber surroundSuper-strength alloyImproved bass handelingImproved dust cap Product details Markaudio Pluvia-11 Gold 7†full Range Aluminium woofer The Pluvia 11 is a completely new driver design. It is the first “full range†driver that can handle bass loads typically delivered by 5.5 inch to 6.5 inch mid-bass units used in most 2 way systems. The Pluvia 11 cone is an entirely new design from Mark Fenlon. It uses a new super-strength aerospace grade alloy designed to cope with high bending stress loads. The material thickness is increased by 50% over previous Markaudio designs, yet the profile remains shallow to increase dispersion. Two more processes have been added to the Multiform cone production sequence to increase Pluvia 11's operational low frequency load capacity. The all-new front suspension has a variable thickness geometry, increasing oscillatory stability by 30% over previous designs. The rear suspension (spider) has an operational surface area 25% larger than the Alpair 10 to cope with load demands of typical mid-bass units. However, the Pluvia 11's high range has not been sacrificed. It outperforms the smaller Alpair 10 by reaching slightly higher frequencies with an improved spread on the high-range lift above 10kHz. Other design advances include the new “easy install†frame. This new-technology one-piece moulding utilises a GF30 glass fibre and resin mix. Pluvia 11's frame is more rigid than previous designs, with a mounting depth of only 4.5mm, making both recessed and surface-mounting simple. Two new cone colours add visual interest. Along with the Pluvia 7, this new family of drivers will serve custom builders well into the future. For the first time in the history of traditional full-range driver design, users now have a genuine choice to go full-range without sacrificing bass handling, or use it as a wide-range mid-bass driver that allows simple filtering. The new Pluvia 11 is an excellent high-end and multi-purpose driver. It's also suitable for many computer, Home Theatre, TV, and commercial A/V applications.Show more Show lessMarkaudio MAOP-7.2 White 4″ Full Range Woofer
The Mark Audio wide band drivers MAOP (Micro Arc Oxidation Process or Plasma Electrolytic Oxidization) have been made in extremely small production runs and are extremely collectable by the local customers. HighlightsEvery pair is matchedMicro Arc Oxidation ProcessCrystalline oxide coneWide band driver Product details Markaudio MAOP-7.2 White 4" Full Range Woofer | Each two drivers are sold as a matched pair. The uniqueness of Markaudio lays on their matching pairs of drivers. Each driver is tested and paired with another driver that shows the closest matching frequency response measurement. In order to respect this philosophy and added value to these great products, we at SoundImports, recomend you to purchase them as pairs. The Magnetic Arc Oxidisation Process is done at extremely high temperature in a flux bath that is prone to differential temperatures (hot/cold spots) which can warp the cones. The process is 10 times the cost of normal cone production, at least half are scrapped as it does render cones unusable if they are warped even slightly. The MAOP process involves a chemical conversion where the cone material is converted into its crystalline oxide. The crystal grows both inward into the substrate and outward. As such the new coating is not a deposited coating it is part of the original structure which gives excellent adhesion. The large crystal structure provides excellent stiffness and resistance to damage. The crystalline structure also encapsulates microscopic voids. It is supposed that it is the blend of microscopic voids and stiff structure that lend the cone the audio properties of both the metal cone and the paper cone, accuracy and a listen all day quality. After construction, each driver is individually measured in the anechoic chamber at the Markaudio factory and pair matched based on that data to within, 0.5% tolerance. Each pair is supplied with individual electrical and acoustic measurements.Show more Show lessMarkaudio MAOP-11 6.5″ Full-range Woofer
The Mark Audio wide band drivers MAOP (Micro Arc Oxidation Process or Plasma Electrolytic Oxidization) have been made in extremely small production runs and are extremely collectable by the local customers. HighlightsMicro Arc Oxidation ProcessCrystalline oxide coneWide band driver Product details Markaudio MAOP-11 6.5" Full-range Woofer The Magnetic Arc Oxidisation Process is done at extremely high temperature in a flux bath that is prone to differential temperatures (hot/cold spots) which can warp the cones. The process is 10 times the cost of normal cone production, at least half are scrapped as it does render cones unusable if they are warped even slightly. The MAOP process involves a chemical conversion where the cone material is converted into its crystalline oxide. The crystal grows both inward into the substrate and outward. As such the new coating is not a deposited coating it is part of the original structure which gives excellent adhesion. The large crystal structure provides excellent stiffness and resistance to damage. The crystalline structure also encapsulates microscopic voids. It is supposed that it is the blend of microscopic voids and stiff structure that lend the cone the audio properties of both the metal cone and the paper cone, accuracy and a listen all day quality.Show more Show lessMarkaudio MAOP-5 3″ Full-range Woofer
The Mark Audio wide band drivers MAOP (Micro Arc Oxidation Process or Plasma Electrolytic Oxidization) have been made in extremely small production runs and are extremely collectable by the local customers. HighlightsEvery pair is matchedMicro Arc Oxidation ProcessCrystalline oxide coneWide band driver Product details Markaudio MAOP-5 3" Full-range Woofer | Each two drivers are sold as a matched pair. The uniqueness of Markaudio lays on their matching pairs of drivers. Each driver is tested and paired with another driver that shows the closest matching frequency response measurement. In order to respect this philosophy and added value to these great products, we at SoundImports, recomend you to purchase them as pairs. The Magnetic Arc Oxidisation Process is done at extremely high temperature in a flux bath that is prone to differential temperatures (hot/cold spots) which can warp the cones. The process is 10 times the cost of normal cone production, at least half are scrapped as it does render cones unusable if they are warped even slightly. The MAOP process involves a chemical conversion where the cone material is converted into its crystalline oxide. The crystal grows both inward into the substrate and outward. As such the new coating is not a deposited coating it is part of the original structure which gives excellent adhesion. The large crystal structure provides excellent stiffness and resistance to damage. The crystalline structure also encapsulates microscopic voids. It is supposed that it is the blend of microscopic voids and stiff structure that lend the cone the audio properties of both the metal cone and the paper cone, accuracy and a listen all day quality. After construction, each driver is individually measured in the anechoic chamber at the Markaudio factory and pair matched based on that data to within, 0.5% tolerance. Each pair is supplied with individual electrical and acoustic measurements.Show more Show lessMarkaudio MAOP-10.2 White 6″ Full Range Woofer
The Mark Audio wide band drivers MAOP (Micro Arc Oxidation Process or Plasma Electrolytic Oxidization) have been made in extremely small production runs and are extremely collectable by the local customers. HighlightsEvery pair is matchedMicro Arc Oxidation ProcessCrystalline oxide coneWide band driver Product details Markaudio MAOP-10.2 White 6" Full Range Woofer | Each two drivers are sold as a matched pair. The uniqueness of Markaudio lays on their matching pairs of drivers. Each driver is tested and paired with another driver that shows the closest matching frequency response measurement. In order to respect this philosophy and added value to these great products, we at SoundImports, recomend you to purchase them as pairs. The Magnetic Arc Oxidisation Process is done at extremely high temperature in a flux bath that is prone to differential temperatures (hot/cold spots) which can warp the cones. The process is 10 times the cost of normal cone production, at least half are scrapped as it does render cones unusable if they are warped even slightly. The MAOP process involves a chemical conversion where the cone material is converted into its crystalline oxide. The crystal grows both inward into the substrate and outward. As such the new coating is not a deposited coating it is part of the original structure which gives excellent adhesion. The large crystal structure provides excellent stiffness and resistance to damage. The crystalline structure also encapsulates microscopic voids. It is supposed that it is the blend of microscopic voids and stiff structure that lend the cone the audio properties of both the metal cone and the paper cone, accuracy and a listen all day quality. After construction, each driver is individually measured in the anechoic chamber at the Markaudio factory and pair matched based on that data to within, 0.5% tolerance. Each pair is supplied with individual electrical and acoustic measurements.Show more Show lessMarkaudio CHR-90 Silver Full-range Woofer
The CHR-90 is an affordable all-new Full-Range 3.5-inch multipurpose driver unit suitable for use in a variety of medium size loudspeakers applications, or as part of a multiway system. HighlightsFull range drive unitWide operating range to 20KHz –very linear responseMetal cone Product details Markaudio CHR-90 Silver Full Range Magnesium Woofer The central mid-range is benign, near flat response, from 1KHz to 6KHz giving end-users and custom builders the potential to use the CHR90 as a mid-field driver in larger multiway applications, useful for balancing out larger radiated surface outputs from big bass units. The CHR90 also has potential for use in 2 way applications as a bass-mid driver. Most Markaudio drivers have a purpose designed frequency lift in the lower ranges (typically 100Hz to 500Hz) to compensate for baffle step losses. The CHR90 is useful to these applications where end-users and loudspeaker makers need a wider choice on frequency cross-over point selection.The CHR90 chassis is an all-new design, dedicated to this driver. All moving parts (powertrain) are new and custom-made for this driver. Much work has been done to make the CHR90 a versatile driver and extend the well-known performance characteristics of Markaudio's products.Show more Show lessMarkaudio CHR-90 Champ Full-range Woofer
The CHR-90 is an affordable all-new Full-Range 3.5-inch multi-purpose driver unit suitable for use in variety of medium size loudspeakers applications, or as part of a multiway system. HighlightsFull range drive unitWide perating range to 20KHz –very linear responseMetal cone Product details Markaudio CHR-90 Champagne Full Range Magnesium Woofer The central mid-range is benign, near flat response, from 1KHz to 6KHz giving end-users and custom builders the potential to use the CHR90 as a mid-field driver in larger multiway applications, useful for balancing out larger radiated surface outputs from big bass units. The CHR90 also has potential for use in 2 way applications as a bass-mid driver. Most Markaudio drivers have a purpose designed frequency lift in the lower ranges (typically 100Hz to 500Hz) to compensate for baffle step losses. The CHR90 is useful to these applications where end-users and loudspeaker makers need a wider choice on frequency cross-over point selection. The CHR90 chassis is an all-new design, dedicated to this driver. All moving parts (powertrain) are new and custom made for this driver. Much work has been done to make the CHR90 a versatile driver and extend the well-known performance characteristics of Markaudio's products.Show more Show lessMarkaudio CHR-70 Silver 4″ Full Range Aluminium Woofer
The MarkAudio CHR-70 has a light easy sound, a little warm, not so "shaped" so it will suit the listening tastes of many people. Its cone gives much musical detail and makes a very clear sound. HighlightsLatest-modelSynthetic rubber surroundNomex spiderImproved voice coil former Product details Markaudio CHR-70 Silver 4" Full Range Aluminium Woofer The CHR-70 (Gen. 3) is now up-dated 3 times since the first model was launched nearly 3 years back. This Gen. 3 driver has more high range performance. The frequency range now goes higher to 25-kHz. Bass response in the properly designed box can go low to just under 40Hz. It has a light easy sound, a little warm, not so "shaped" so it will suit the listening tastes of many people. Its cone gives much musical detail and makes a very clear sound. The driver has a medium efficiency of 85.5 dB at 8 Ohms making it easy to use on nearly all small to medium power amplifiers. The driver can easily fit into Bass-reflex and Vented box sizes from 4.4 liters to 10 liters internal volume. Many technical improvements have been made. Improved stiffer frame. New cap design with a new improved fitting method. New Japanese designed coil. New spider for improved bass. The new CHR-70 Gen. 3 is an excellent high-end and multi-purpose driver. Its also suitable for many computers, Home Theatre, TV, and commercial A/V applications.Show more Show lessMarkaudio CHR-70 Black 4″ Full Range Aluminium Woofer
The MarkAudio CHR-70 has a light easy sound, a little warm, not so "shaped" so it will suit the listening tastes of many people. Its cone gives much musical detail and makes a very clear sound. HighlightsThe latest model, 3rd generationSynthetic rubber surroundNomex spiderImproved voice coil former Product details Markaudio CHR-70 Black 4" Full Range Aluminium Woofer The CHR-70 (Gen. 3) is now up-dated 3 times since the first model was launched nearly 3 years back. This Gen. 3 driver has more high range performance. The frequency range now goes higher to 25-kHz. Bass response in the properly designed box can go low to just under 40Hz. It has a light easy sound, a little warm, not so "shaped" so it will suit the listening tastes of many people. Its cone gives much musical detail and makes a very clear sound. The driver has a medium efficiency of 85.5 dB at 8 Ohms making it easy to use on nearly all small to medium power amplifiers. The driver can easily fit into Bass-reflex and Vented box sizes from 4.4 liters to 10 liters internal volume. Many technical improvements have been made. Improved stiffer frame. New cap design with a new improved fitting method. New Japanese designed coil. New spider for improved bass. The new CHR-70 Gen. 3 is an excellent high-end and multi-purpose driver. Its also suitable for many computers, Home Theatre, TV, and commercial A/V applications.Show more Show lessMarkaudio CHR-120 6.5″ Grey Full Range Magnesium Woofer
HighlightsLatest-modelAerospace-grade magnesium-alloyWide dispersion multiform cone conceptOptimized for use in larger enclosures Product details Markaudio CHR-120 6.5" Grey Full Range Magnesium Woofer The CHR-120 is a brand-new 6.5-inch high fidelity multi-purpose high-volume driver design from Markaudio. This new driver has been purpose developed to provide significant bass extension beyond what many similar-sized midbass units can deliver, combined with full-range frequency output. The CHR-120 cone is made from a high-strength, aerospace-grade magnesium-alloy designed to cope with high bending stress loads. Based upon our renowned shallow profile, wide dispersion multiform cone concept, the material thickness is carefully balanced to maximize low-frequency load capacity while retaining excellent performance at higher frequencies. The long-stroke suspension and low-distortion motor are designed to provide a low resonant frequency, medium Q, and an air volume compliance of around 59 liters. Optimized for use in larger enclosures, the CHR-120 can provide output to some 30Hz and smooth high-frequency range extending above 20KHz in a suitable design. Other key features include an “easy install†reinforced polymer frame for both surface and recessed mounting. The CHR-120 provides custom builders with wide operational flexibility at a surprisingly affordable price and can be used as a high-performance full-range driver, or as a wide-range midbass. It is ideal for use in high-fidelity, home-theatre, commercial A/V applications, and by suiting a wide range of enclosure types, it continues Markaudio's reputation for providing qualitative excellence and advanced mechanical engineering at an accessible level.Show more Show less
